New

6AG1542-5DX10-7XE0

Condition: New product

More info

Siemens 6AG1542-5DX10-7XE0

SIPLUS S7-1500 CM 1542-5 based on 6GK7542-5DX10-0XE0 with conformal coating, -40…+70 °C, start up -25 °C, communications module for connection of S7-1500 to PROFIBUS DP as DP master and DP Device: S7 and PG/OP communication, time-of-day synchronization, diagnostics

product type designation		CM 1542-5
Technical Product Detail Page		https://i.siemens.com/1P6AG1542-5DX10-7XE0
transfer rate
transfer rate
● at the 1st interface / according to PROFIBUS		9.6 kbit/s ... 12 Mbit/s
interfaces
number of interfaces / according to Industrial Ethernet		0
number of electrical connections
● at the 1st interface / according to PROFIBUS		1
type of electrical connection
● at the 1st interface / according to PROFIBUS		9-pin Sub-D socket (RS485)
supply voltage, current consumption, power loss
type of voltage / of the supply voltage		DC
supply voltage / 1 / from backplane bus		15 V
relative symmetrical tolerance / at DC
● at 15 V		3 %
consumed current
● from backplane bus / at DC / at 15 V / typical		0.2 A
power loss [W]		3 W
ambient conditions
ambient temperature
● for vertical installation / during operation		-40 ... +40 °C
● for horizontally arranged busbars / during operation		-40 ... +70 °C
● during storage		-40 ... +70 °C
● during transport		-40 ... +70 °C
● note		Startup @ -25 °C
installation altitude / at height above sea level / maximum		5000 m
ambient condition / relating to ambient temperature - air pressure - installation altitude		Tmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m) // Tmin ... (Tmax - 10 K) at 795 hPa ... 658 hPa (+2 000 m ... +3 500 m) // Tmin ... (Tmax - 20 K) at 658 hPa ... 540 hPa (+3 500 m ... +5 000 m)
relative humidity
● with condensation / according to IEC 60068-2-38 / maximum		100 %; RH including condensation/frost (no commissioning when condensation is present), horizontal installation
chemical resistance / to commercially available cooling lubricants		Yes; incl. airborne diesel and oil droplets
resistance to biologically active substances
● conformity according to EN 60721-3-3		Yes; Class 3B2 mold and fungal spores (excluding fauna), Class 3B3 on request
● conformity according to EN 60721-3-6		Yes; Class 6B2 mold, fungal and dry rot spores (excluding fauna)
resistance to chemically active substances
● conformity according to EN 60721-3-3		Yes; Class 3C4 (RH < 75 %) incl. salt spray in accordance with EN 60068-2-52 (Severity 3). The supplied plug covers must remain in place on the unused interfaces during operation.
● conformity according to EN 60721-3-6		Yes
resistance to mechanically active substances
● conformity according to EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied plug covers must remain in place over the unused interfaces during operation.
● conformity according to EN 60721-3-6		Yes; Class 6S3 incl. sand, dust. The supplied plug covers must remain in place over the unused interfaces during operation.
coating / for equipped printed circuit board / according to EN 61086		Yes; Class 2 for high availability
type of coating / protection against pollution according to EN 60664-3		Yes; Protection of the type 1
type of test / of the coating / according to MIL-I-46058C		Yes; Coating discoloration during service life possible
product conformity / of the coating / Qualification and Performance of Electrical Insulating Compound for Printed Board Assemblies according to IPC-CC-830A		Yes; Conformal coating, class A
protection class IP		IP20